Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Hobe Sound
Gate repair in Hobe Sound usually means one of two things: a swing gate that’s sagged or seized on corroded hinges, or an operator that won’t respond because salt air has fouled the low-voltage wiring and photo-eyes. We handle both, along with everything from bent posts to failed control boards. If your gate is stuck, grinding, or refusing to open, call us at (855) 382-0732. We know the Hobe Sound coast and what it does to gate hardware, and we come prepared for it.
Why Miami Gardens Gate Repair Is Hobe Sound’s Preferred Gate Repair Company
Gates are all we do. No garage doors, no fencing side jobs, no general handyman work. That single-trade focus is why Hobe Sound property owners call us when a LiftMaster swing operator stalls halfway or a FAAC slide gate on a long private drive won’t travel smoothly. Our technicians work on nine major gate brands including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If you own a gate in Hobe Sound, we almost certainly know the exact model and its failure points.
We’re not a franchise operation with rotating crews. The same specialists who diagnose a corroded control board in Jupiter will be the ones inspecting your gate column off SE Bridge Road. That matters on the coast, where the first repair attempt usually succeeds only if someone has already seen what salt air does to a specific brand’s limit switches and wiring splices. Homeowners in Hobe Sound call us because we treat the actual fault, not the symptom, and because we carry the parts to do it in one visit.
Our team covers all of Hobe Sound, including ZIP codes 33455 and 33475, from the Intracoastal corridor to the western ranchettes. We work on the ornamental gates along Bridge Road and the newer gated communities near Jupiter Island, and we schedule so a repair on one side of town isn’t delayed by traffic on US-1. Call (855) 382-0732 and you’ll speak to someone who understands coastal gate work specifically.
Styles & brands we work with
Iron Gate Repair in Hobe Sound
Iron gate repair in Hobe Sound carries a different set of problems than the same job twenty miles inland. The ornamental iron gates on the estate properties along the Intracoastal and the barrier-island side take a beating from salt spray and wind-driven sand. Pivot hinges pit. Welds rust from the inside out. Gate posts that looked plumb when installed start leaning as the base steel corrodes. We realign, re-weld, and when the damage is too far gone, we’ll tell you honestly whether repair or replacement makes more sense.
Hinge and Post Repair
A sagging iron gate in Hobe Sound is almost never just an adjustment issue. Salt air eats the hinge barrels and the post steel, and blowing sand accelerates the wear at the pivot. We cut out rotted sections, weld in new steel, and reset the post so the gate hangs square and swings without dragging. If the post itself has corroded below grade, we handle that too, including setting a new footing where needed.
Weld and Rust Repair
Rust on an ornamental gate in Hobe Sound is not cosmetic. Once the protective coating fails, the salt air works fast, and what starts as bubbling paint becomes weakened pickets and cracked welds within a couple of seasons. We grind back to clean steel, weld the cracked joints, and treat the surface so the repair isn’t just a patch. For coastal gates, we recommend galvanised steel and stainless fasteners from the start. Painted mild steel will not hold up on the Intracoastal over the long haul, no matter how well it’s coated initially.
Sliding Gate Repair in Hobe Sound
Sliding gate repair in Hobe Sound most often shows up on the long private drives off Bridge Road and the acre-plus properties in 33455 and 33475, where a cantilever or track-style slide gate covers a wider opening than a swing gate can manage. The motor matters, but it’s rarely the first thing to fail here. Salt air corrodes the limit switches, the photo-eye connections at the gate column, and the low-voltage wiring that runs through buried conduit. We fix the mechanical track issues and the electronic faults together, because treating one without checking the other means a callback you shouldn’t need.
Gate Realignment
A slide gate that grinds or shudders as it travels is usually fighting a misaligned track or a wheel assembly that’s worn unevenly. On coastal Hobe Sound properties, sand and salt grit work their way into the rollers and accelerate that wear. We reset the track, replace the wheels or bearings that need it, and test the travel under load so the operator isn’t straining against a gate that’s out of line.
Operator Diagnostics
When an Electric Gate Repair call comes in from Hobe Sound, more than half the time the motor tests fine. The culprit is a salt-fouled safety photocell, a corroded splice in the low-voltage run, or a control board that took a surge during the last storm. We diagnose the entire system, from the actuator to the access keypad, and we repair what’s actually failed rather than swapping a motor that had years left in it.
Trusted Brands We Service in Hobe Sound
Hobe Sound gates run on every major operator brand, and we work on all of them. LiftMaster, FAAC, Elite, and Mighty Mule are the ones we see most often out here, but our technicians are trained and experienced across nine brands total, so a BFT actuator or a Viking control board is no mystery to us. That brand-spanning knowledge changes the repair conversation. We don’t push a replacement when a control board repair is the right call. We can source the part for your specific operator, often same week, and our familiarity with how these systems fail on the coast means we carry the components that Hobe Sound properties actually need.
Common Gate Repair Problems We See in Hobe Sound Homes
- Intermittent ‘gate won’t open’ faults: On barrier-island and Intracoastal-side estates, salt spray and blowing sand corrode the low-voltage photo-eye and keypad wiring at the gate column. The motor is often fine. The real fault is a fouled lens or a corroded splice, and that’s what we find and fix.
- Seized and leaning hinge posts: Salt air works on the post steel below the hinge plates. The gate starts to sag, the operator works harder, and eventually the swing gate binds. We replace the post section or reset the footing, then re-hang the gate so it sweeps clean.
- Control board failures after storms: Hurricane-season power surges and lightning strikes along the Intracoastal corridor knock out control boards and limit switches on solar slide operators and swing gate actuators. We test the board, replace or repair it, and check the grounding and surge protection so the next storm doesn’t repeat the damage.
- Track and roller wear from sand: Gates on acre-plus properties with long driveways collect sand in the track and roller assemblies. Hobe Sound’s blowing sand accelerates that wear, leading to grinding, jerky travel, and a motor that overheats trying to compensate. We clean, realign, and replace worn components before the operator burns out.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Hobe Sound, FL
A basic gate realignment or hinge adjustment in Hobe Sound typically runs $150 to $350, depending on the gate’s size and how far out of line it’s gotten. Iron gate hinge and post repair on a coastal property, where steel sections need to be cut out and re-welded, usually lands between $400 and $1,200. Electric gate repair calls that involve a control board, actuator, or photo-eye replacement run $350 to $1,800, with the higher end covering dual-slide operators and access system faults. Every price is quoted and agreed before any work starts. You will know the number before we turn a wrench, and our estimates are free. Call (855) 382-0732 for an exact quote on your gate.
We Also Serve Cities Near Hobe Sound
Our Gate Repair team covers Hobe Sound and the surrounding communities, including Port Salerno, Tequesta, Stuart, and Jupiter. If your property sits on the northern edge of Hobe Sound near the Tequesta line or south toward the Stuart border, you’re in our normal service area. For full coverage details, see our Gate Repair in Hobe Sound page or call us directly at (855) 382-0732.
Serving Hobe Sound, FL — Our Local Coverage Area
We’re based in the Hobe Sound area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Hobe Sound
On Hobe Sound’s Intracoastal and barrier-island properties, intermittent gate failures are usually caused by corroded low-voltage wiring or a salt-fouled photo-eye lens at the gate column, not the motor. The salt-laden onshore air gets into splices, keypad connections, and safety photocells, creating resistance and signal dropouts that come and go with humidity and temperature changes. We test the entire circuit, find the corroded connection, clean or replace it, and the gate stops acting up. Call (855) 382-0732 and we’ll diagnose it properly.
On most coastal Hobe Sound properties, the first failures happen at the pivot hinges and the low-voltage photo-eye wiring at the gate column, not in the motor or the gearbox. Salt spray pits the hinge steel and the post, while the safety photocell lens gets fouled with salt film and blowing sand. If those fail, the operator works blind and the gate stalls or won’t open. We check these first because they’re the most common failure points here, and fixing them costs far less than a motor replacement.
For any gate within a mile of the Intracoastal or the Atlantic in Hobe Sound, galvanised steel is the right call, and stainless fixings are not optional. Painted mild steel looks fine for the first couple of seasons, but once salt air reaches the steel through a scratch or a rubbed spot, it rusts from the inside out. Galvanised steel, properly welded and touched up at the joints, survives the coastal environment for far longer. We can re-spec your existing gate during a repair or advise on materials for a new installation.
Yes, every automatic gate in Hobe Sound, residential or commercial, needs working entrapment protection, which usually means a photo-eye system and a reversing mechanism on the operator. The UL 325 standard applies, and on coastal properties those photo-eyes fail earlier than anything else because of salt film and sand on the lenses. If your gate doesn’t reverse when something crosses the beam path, it’s unsafe, and you should call us at (855) 382-0732 to test and repair the system before someone gets hurt.
On Hobe Sound’s acre-plus properties, a jerky or grinding slide gate is usually a track and roller problem, often worsened by sand and salt grit built up in the wheel assemblies. The operator then labors against the resistance, and if left alone, it will burn out the motor. We clean the track, replace worn rollers or bearings, realign the gate, and verify the operator’s force settings so the system travels cleanly. Call us at (855) 382-0732 for a free estimate on a repair or replacement.
Contact Miami Gardens Gate Repair for Hobe Sound Service
If your gate is stuck, stalled, or showing signs of coastal corrosion, call (855) 382-0732 for a free estimate. We cover all of Hobe Sound, from the Intracoastal estates off SE Bridge Road to the ranchettes and gated communities across 33455 and 33475. We’ll come assess the gate, explain what’s failed and why, quote the repair before we start, and fix it right the first time. Gates are all we do, and on the Hobe Sound coast, that focus makes the difference.
Written by Noel Carballo, Owner at Miami Gardens Gate Repair, serving Hobe Sound and the surrounding coastal communities.